PSA Oxygen Generation
Pressure Swing Adsorption (PSA) is an advanced gas separation technology in which a molecular sieve adsorbs gases under pressure and releases them when the pressure is reduced, in a repeating cycle. A PSA oxygen plant uses a dedicated adsorbent at ambient temperature to concentrate oxygen from air: nitrogen, carbon dioxide and moisture are adsorbed, while oxygen passes through. The product gas normally contains oxygen, argon and a small amount of nitrogen. Key enabling technologies are high-performance program-controlled valves, oxygen-enrichment adsorbents and process design.
Typical PSA oxygen unit
- Capacity: 50, 80, 100, 120, 150 Nm³/h
- Oxygen purity: 90%–95%
- Oxygen outlet pressure: 0.4–0.5 MPa
- Energy consumption: ≤ 0.35 kWh/m³ O2
Operating principle
Oxygen and nitrogen are separated by the difference in their adsorption on zeolite molecular sieve (ZMS) at different pressures. There are two process routes, chosen according to operating conditions to minimize unit consumption:
- Atmospheric desorption (PSA-O): compressed air is pretreated to remove oil, dust and most water vapor, then enters adsorption towers filled with ZMS. Once loaded, the adsorbent is regenerated by desorption to atmosphere.
- Vacuum desorption (VPSA-O): blower air is cleaned of dust and enters the towers; after desorption to atmosphere, a vacuum pump fully regenerates the adsorbent.
Two- or three-tower systems switch cyclically under PLC or DCS control for continuous oxygen production.
Features
- Simple, compact process with low capital cost and small footprint; indoor or outdoor installation
- Highly automated, with quick start-up and shutdown
- Lower operating and maintenance cost than cryogenic oxygen production
- Stable and reliable, operating safely at ambient temperature and low pressure
- Plant size 0.2–5500 Nm³/h; oxygen purity 25–95%
- Outlet pressure 0.3–0.55 MPa (atmospheric desorption) or 15 kPa (vacuum desorption); boosting options available
Main components
Air compressor or blower; air pretreatment (oil, dust and water removal, cooling); adsorption towers; air and product oxygen buffer tanks; switching valves and manifolds; vacuum pump (vacuum desorption); oxygen booster and filling equipment; automatic control and purity monitoring; purity adjustment and gas blending system.
Installation requirements
The site should be clean, level and accessible by crane or forklift, with clean, well-ventilated air free of oil mist and corrosive gases. Utilities: 380 V / 50 Hz / 3-phase 5-wire power and industrial cooling water.
Selection guidance
Confirm the product gas requirements first and determine the process with the manufacturer. Evaluate design rationality, operating reliability and the manufacturer’s capability, and calculate total cost, including utilities, site, maintenance and service life, rather than purchase price alone.
Applications
- Electric furnace steelmaking, non-ferrous smelting, oxygen-enriched ironmaking
- Fertilizer gasification, chemical oxidation, coal gasification, ozone generation
- Combustion enhancement for industrial furnaces and foundry cupolas
- Pulp digestion and bleaching, black liquor oxidation
- Activated sludge treatment of industrial and municipal wastewater
- Naphtha cracking and carbon black production
- High-density aquaculture
- Cement, refractory brick and glass processing
- Medical and healthcare oxygen, hyperbaric chambers
Membrane Separation
Membrane separation uses the selective permeability of polymer membranes to separate oxygen and nitrogen in air. Hollow-fiber modules contain tens of thousands of polymer fibers. Gas molecules adsorb and dissolve at the membrane surface, diffuse through it and desorb on the other side. Under a pressure difference, fast gases such as water vapor, oxygen, hydrogen, helium, hydrogen sulfide and carbon dioxide permeate, while slower gases such as nitrogen, argon, methane and carbon monoxide remain on the retentate side. Capacity and purity are limited; the method is generally used for nitrogen below 800 Nm³/h and below 99.5% purity.
Membrane nitrogen (high-pressure process)
Compressed air is pretreated and preheated, then enters the membrane separator. Fast gases are vented from the permeate side and nitrogen is concentrated on the retentate side, delivering continuous stable nitrogen under PLC or DCS control.
- Reaches target purity within 10 minutes
- No switching valves or other moving parts, so little maintenance
- Output easily expanded by adding separators
- Lower operating cost than PSA nitrogen, with excellent value at 80–98% purity
- Plant size 0.2–50000 Nm³/h; nitrogen purity 80–99.9%
Main components: air compressor, air pretreatment, air buffer tank, membrane separators, product nitrogen buffer tank, valves and piping, automatic control and monitoring, optional booster system.
Membrane oxygen
In membrane oxygen production, oxygen is enriched on the permeate side. Two processes are available: a high-pressure process, in which compressed air is pretreated and preheated before the separator, and a negative-pressure process, in which blower air is cleaned, slower gases are discharged from the retentate side, and a vacuum pump collects the oxygen-enriched permeate.
- Reaches target oxygen concentration within 10 minutes
- No switching valves or moving parts, so little maintenance
- Lower operating cost than PSA oxygen, with excellent value at 25–35% purity, especially for combustion enhancement
- Plant size 0.2–50000 Nm³/h; oxygen purity 25–45%
Installation requirements and selection guidance are the same as for PSA systems.